The Olight Warrior 3S is the successor to the Warrior 3 with just one physical difference, and one new feature which is proximity sensor. All other specs, including lumen outputs and operations remain same as before.
Both these models update the famous M2R Pro warrior with a top output, and design changes to both the side switch and tail switch, yet retain the compact size, 21700 lithium-ion battery energy source and deeper knurling design.
It is capable of 2300 lumens output on the top turbo settings, before dropping down to 800 lumens after 2.5 minutes continue use, and then after a further two hours forty minutes the output will drop again 250 lumens to stop the LED from overheating. The LED has been replaced to a cool white LED, which gathered with a TIR reflector generates a standard defined hot spot with a spill light for a best all round beam profile, and can reach up to a highest of 300 metres beam range.
Quick glance
- The Warrior 3S is a strong dual-switch tactical flashlight with a proximity sensor.
- The cool white LED paired with a TIR optic lens delivers up to 2,300 lumens.
- It specs six output settings that can be picked on demand using the side switch.
- The newly adopted proximity sensor drops the level of brightness proactively in case of obstruction.
- Its tailcap is compatible with an optional lock-on dual-bottom remote switch for WML application.
- Powered by 21700 5000mAh battery, it changes simply by the MCC3 cable.
- The four level battery and brightness indicators around the side switch which forever keep you informed about its status.
Features
Long battery time
It is powered using the included Olight 21700 5000 mAh customised lithium-ion battery, which is recharged within the flashlight using the included MCC3 magnetic charging cable. Just connect the magnet to the base of the Warrior 3S and the plug the USB-A. The indicator light on the magnet will go red while charging is in progress and turn green once charging is done after approximately five hours, thirty minutes when using a 5V, 2A output.
The detachable dual pocket clip can be linked to clothing simply from both sides while the powerful holster is best for carrying the Warrior 3S on your belt and it also specs a flap with clip fastening to ensure your flashlight stays safe while you are on the move.
Tail switch
In configuration 1 with the Warrior 3S tail switch will access turbo with a fast deep press and release or mid with a fast half press and release. If the key is pressed and held then the light will enter momentary illumination in the corresponding output and light will turn off when the button is released. In configuration 2 it will give momentary access to turbo with a half press and grip, or momentary access to strobe with a deep press and grip.
A handy lockout function stops the flashlight from being accidentally activated and is accessed by pressing and gripping the side switch for two seconds. It will enter moonlight mode first and then go into lockout. The unlock press and grip the button for over two seconds until the moonlight mode comes back on.
Multi-function side-switch
The multi-function side-switch turns the flashlight off and on with each press and cycles via the brightness modes of mid, low, and high when you hold down the side key with the light on. For turbo access you twin click the button and a trip click enters strobe. Moonlight mode can be accessed by gripping the button down the light is off. The memory function will remember the end mode used for low, moonlight, and high.
When the light is turned on the indicator switch either side of the key will illuminate. The indicators up the left hand side are to show the mode you are in with the first one for low or moonlight, the second one for mid, the third one for high and the fourth one for turbo. The indicators up the right hand side are indicators for battery level and the bottom first one shows 10-25 percent power, the second one is 25-50 percent power, the third one is 50-75 percent power and the fourth one is above 75 percent power.
Thermal management system
The Warrior 3S also specs a nifty proximity sensor that will mechanically decrease the output if the head of the flashlight becomes too near to an object when it is setting three or higher so that the heat expelled from the flashlight does not cause any issue.
Advantages
New LED, upgraded output
Its cool white LED, combined with the TIR optic lens, delivers up to 2,300 lumen high output to reach far into the darkness to light up any atmosphere.
Better protection
Built-in proximity sensor that drops the brightness level to save against any nearby objects while turned on turbo, high, or strobe mode
Long run-time tactical flashlight
Features up to fifty-five days runtime making this the best tactical light for camping, hiking, self-defense, and law enforcement with its amazing performance!
Upgraded & multi-functional tail switch
The tailcap is compatible with new dual-key magnetic remote switch for professional users to control it as a WML, and the tailswitch specs a dual pressure design permitting to access strobe or turbo with a one press.
Visualized indicators
Four level battery and brightness indicators around the switch, which can be read at a one glance.
End words
The warrior 3S is a strong dual-switch tactical torch with a proximity sensor. The cool white LED paired with a TIR optic lens delivers up to 2300 lumens. It specs six output settings that can be picked on-demand using the side switch. For tactical operations, the dual-stage tail switch permits fast and simple access to the most vital settings such as strobe and turbo. The newly adopted proximity sensor drops the brightness level proactively in case of obstruction. Powered by a 5000mAh 21700 battery, it charges simply by the MCC3 cable. The four level battery and brightness indicators around the side switch forever keep you informed about its status.
